You are here
NEW VERSION WITH DOUBLE CONSTELLATION GPS+GLONASS RECEIVER ALLOWING UNMATCHED PRECISION LEVELS, WITH SPECIAL BLUE SILICONE BUTTONS AND GASKETS FOR A FRIENDLY TOUCH AND EXTRA SEALING. |
|
|
THE FIRST GPS LAP TIMERS IN THE WORLD TOTALLY
|
IF YOU DON'T WANT TO USE YOUR COMPUTER OR PRESS BUTTONS ON THE TRACK, THE SAFD-2 FEATURE (Starlane Automatic Finish line Detection), WILL SPLIT AUTOMATICALLY THE TRACK AFTER THE FIRST 2 LAPS RUN, ALLOWING YOU TO SEE YOUR LAP TIMES AND INTERMEDIATES FROM THE VERY FIRST SESSION WITHOUT ANY ACTION ON THE LAP TIMER. |
With S.E.P.L.A. (Starlane Enhanced Precision Laptiming Algorithm) feature: a lap timing algorithm allowing very high laptiming precision levels. |
STEALTH GPS-4 allows the data download directly on your USB pendrive, with this solution you can enjoy it without bringing your computer on the track area. Digirace-MMX software will automatically recognize your USB pendrive and the new sessions to be downloaded. Another feature making unique Stealth GPS-4 is the possibility to be connected to the optional CAN BUS expansion module that allows the acquisition from external sensors (eg. throttle, gear, RPM, etc.), making your lap timer a data acquisition system. |
Data Overlay rendered by Starlane DigiRace-MMX 2.0 |
RID expansion module is available in 3 versions all including a tri-axial ±8G accelerometer:
RID MOTO (code RID1M)
RID KART (code RID1K)
RID ANALOG-3 (cod. RID1A3) Many RID modules can be connected in line on Stealth GPS-4 CAN BUS increasing the available inputs. The sensors are optional and available on Starlane catalog, some inputs as for eg. RPM, TPS and WHEEL SPEED, can be accessed directly from the original sensors available by factory on the most common motorbike models. |
RID-LAMBDA comes with BOSCH LSU4 Wide Band Lambda sensor and allows the acquisition of Air/Fuel, RPM and Throttle Position values to achieve the best mapping for your engine management system. |
RPM-TPS-AFR Screen |
STEALTH GPS-4 FEATURES |
1) DOUBLE CONSTELLATION GPS+GLONASS RECEIVER AND ANTENNA BUILT IN THE INSTRUMENT: the Stealth shock-proof ABS body accommodates the new double constellation receiver which uses in symbiosis the american GPS and the russian GLONASS satellite systems. This solution increases dramatically the precision due to the vero high number of satellite involved in instantaneous position, speed, trajectory and lap time determination. 2) YOU CAN SAY GOOD-BYE TO ALL UNPRACTICAL INFRARED TRANSMITTERS ARRANGED ON THE PIT WALL: 3) MANAGEMENT OF THE FINISH LINE AND 3 INTERMEDIATES: 4) INDICATION OF THE ACHIEVABLE IDEAL TIME: 5) DOUBLE FUNCTION "BEST LAP" LED: 6) GPS SPEED MEASUREMENT: 7) DOUBLE HOUR METER FOR THE PERFECT PERIODICAL MAINTENANCE OF THE VEHICLE: 8) DATA DOWNLOAD TO USB PENDRIVE: |
9) THE DIGIRACE-MMX SOFTWARE: it's always possible to download from the website the DigiRace-MMX software that can file, analyse and print the data acquired and graphically represent the paths you have driven across with the relative acceleration and deceleration points for a lap-by-lap comparison. |
10) 999-LAP MEMORY WITH AUTOMATIC MANAGEMENT OF 99 TEST SESSIONS: STEALTH GPS-4 will automatically create a new session whenever you access the track. This means that you can analyse the times you have stored during the various sessions even at the end of the day without having to delete memory whenever you access the track. You can store the Date and Time of every single session as well as the total time, the intermediates, the maximum speed for every single lap. 11)CYCLICAL MEMORY MANAGEMENT: 12) STORAGE OF THE FINISH LINE COORDINATES OF THE TRACKS MOST USED: 13) STEALTH GPS-4 IS COMPLETE WITH A BACKLIT LARGE-SIZE GRAPHICAL DISPLAY: 14) EXTERNAL SUPPLY: 15) WATER-RESISTANCE: |
The analysis software DigiRace-MMX can be downloaded for free below... |
Specifications:
|
Content of the package for Stealth GPS-4 Lite (COD. CSTHGPS4LT):
- N° 1 STEALTH GPS-4 Instrument
- N° 1 Elastic support kit
- N° 1 Dual Lock Adhesive strap fastening kit
- N° 1 Supply cable from 12V vehicle battery
- N° 2 Plastic ties for USB socket fixing
- N° 1 User Manual
ACCESSORIES AND SPARE PARTS
RID MOTO - Code: RID1M
CAN BUS module with inputs for: RPM, WHEEL SPEED, GEAR + 3 analog channels + Triaxial Accelerometer. |
RID LAMBDA - Code: RID1LRT
CAN BUS module with Lambda Sond Bosch LSU4 and inputs for RPM and TPS. |
RID ANALOG-3 - Code: RID1A3
CAN BUS module with N° 3 generic analog inputs + Triaxial Accelerometer. |
RID KART - Code: RID1K
CAN BUS module with inputs for: RPM, WATER TEMP., WHEEL SPEED, GEAR, THERMOCOUPLE type K + Acceler. |
PROFESSIONAL LINEAR SENSOR POT. 150 MM. CONN. M8 - Code: SSLIN150PROM8
Slim stem Linear potentiometric sensor 150mm with M8 plug. |
PROFESSIONAL LINEAR SENSOR POT. 75 MM. CONN. M8 - Code: SSLIN075PROM8
Slim stem linear potentiometric sensor 75mm stroke M8 plug. |
LINEAR SENSOR POT. 75 MM. CONN. M8 - Code: SSLIN075M8
Linear potentiometric sensor 75mm. Stroke-Rear Suspension M8. |
LINEAR SENSOR POT. 150 MM. CONN. M8 - Code: SSLIN150M8
Linear potentiometric sensor 150mm. Stroke-Front Suspension M8. |
60BAR BRAKE PRESSURE SENSOR CONN. M8 - Code: SSPBK60M8
Brake pressure 60 BAR sensor M10X1 thread conn. M8. |
MALE-FEMALE 50CM PATCH CONN. M8 - Code: PR50M8
Male-Female 50cm sensor patch cable. |
MALE-FEMALE 100CM PATCH CONN. M8 - Code: PR100M8
Male-Female 100cm sensor patch cable. |
MALE-FEMALE 150CM PATCH CONN. M8 - Code: PR150M8
Male-Female 150cm sensor patch cable. |
ANALOG / SPEED SIGNAL CONNECTION TAIL 20CM - Code: TAP2020
Tail for factory analog ( e.g. Throttle) and vehicle speed sensor connection 20cm. long. |
WATER TEMPERATURE SENSOR M10X1 - Code: CH2OM10
Water temperature sensor M10X1 to be mounted on the optional water manifolds. |
WATER MANIFOLD 26MM. DIAM. FOR SENSOR M10X1 - Code: MAN26
Water manifold 26mm. diam. to be used with water sensor code CH2OM10. |
WATER MANIFOLD 19MM. DIAM. FOR SENSOR M10X1 - Code: MAN19
Water manifold 19mm. diam. to be used with water sensor code CH2OM10. |
WATER MANIFOLD 10MM. DIAM. FOR SENSOR M10X1 - Code: MAN10
Water manifold 10mm. diam. to be used with water sensor code CH2OM10. |
INFRARED TYRE TEMPERATURE SENSOR CONN. M8 - Code: SSIRTP05M8
Infrared non-contact tyre temperature sensor M8. |
BATTERY CASE FOR DOUBLE 9VOLT BATTERY - Code: BPP3C3
External battery case for double 9VOLT commercial batteries type PP3 for Stealth GPS-3/4 and Athon XS. |
7,4V 2,2AH LI-ION BATTERY - Code: BLI07422
7,4V 2,2Ah Lithium-Ion Battery to be charged only by the specific charger code: BCLIMV. |
11,1V 2,2AH LI-ION BATTERY - Code: BLI11122
11,1V 2,2Ah Lithium-Ion Battery to be charged only by the specific charger code: BCLIMV. |
BATTERY CHARGER FOR LI-ION MULTIVOLTAGE - Code: BCLIMV
Battery charger for Li-Ion BLI07422, BLI11126 and BLI11122 Batteries. |
INDUCTIVE SPEED SENSOR Ø 8 MM. - Code: SSPRI8
NPN inductive speed sensor
|
MAGNETIC SPEED SENSOR 8 MM CONN M8 - Code: SSPRMG8M8
Magnetic speed sensor (to be used with magnets code MAG6X2). |
SENSOR BRACKET - Code: SMB
Mounting bracket for 8mm diam. sensors. |
FRONT AXLE MAGNET RING FOR KART - Code: REOKA
Front axle ring with magnets for kart speed signal (to be used with SSPRMG8M8 speed sensor). |
REAR AXLE MAGNET RING FOR KART - Code: REOKP
Rear axle ring with magnets for kart speed signal (to be used with SSPRMG8M8 speed sensor). |
MAGNET 6X2MM FOR SPEED SENSOR - Code: MAG6X2
Magnet 6mm diameter X 2mm thickness to be used with speed sensor SSPRMG8M8. |
ATHON FIXING KIT FOR MOTOCROSS-SUPERMOTO - Code: KITSUPATHMOT
Support Plate kit for Motocross and Supermoto hadlebar raiser for Stealth GPS 2-3-4, Corsaro and ATHON GPS. |
ATHON VELCRO STRIP SUPPORT - Code: KITSUPATHSTP
Support kit with velcro strip system for Stealth 2-3-4, Corsaro and ATHON GPS. |
POWER SUPPLY CABLE STEALTH GPS-3/4 AND ATHON XS - Code: ASPS100M8
Power supply cable for Stealth GPS-3/4 and Athon XS. |
THERMOCOUPLE K AMPLIFIER CONN. M8 - Code: DAMTKM8
Thermocouple type K amplifier conn.M8 for thermocouple sensor code STKSP and STKM5E. |
THERMOCOUPLE TYPE K THREAD M5 - Code: STKM5GS
Professional Exhaust Temperature Sensor with exposed joint, M5 male thread. |
THERMOCOUPLE TYPE K M12 - Code: STKM12GS
Professional Exhaust Temperature Sensor with exposed joint, M12 female flange. |
Download DIGIRACE-MMX 2.01 DIGIRACE-MMX SOFTWARE FOR THE ANALYSIS AND PRINTING OF ACQUIRED TEST SESSIONS
The main functions of DIGIRACE-MMX 2.01:
GPS TRACK
PATHS COMPARISON
|